Hydac CMU 1000 User Manual download pdf (Page 34)

Condition Monitoring Unit CMU 1000 Page 34

Revised 17.12.2009 HYDAC ELECTRONIC GMBH Mat.-No.: 669749

• To set up a connection with one "Slave" CMU (e.g. Address d), proceed as

follows:

• Select Change in the Pass-through mode line. The following window opens:

• Select the HSI channel in the selection window to which the slave devices are

connected (in our example, Port H at the "Master" CMU).

• Afterwards, click on Switch on in order to switch on the pass-through mode for

the selected channel.

• The following message appears:

• Confirm this with OK.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 121 122

Condition Monitoring Unit 1
CMU 1000 1
Table of Contents 3
Preface 8
1 General 9
1.3 Copyright Protection 10
1.4 Note on Warranty 10
2 Safety 11
2.2 Proper/Designated Use 12
2.3 System Configuration 12
3 Setup and Function 13
3.3 Terminal Allocations 14
IO-Link 15
3.4 Examples of Connections 16
3.4.2 Standard HSI Sensors 17
3.4.5 GSM Module CSI-F-10 18
4.1 Installation Guidelines 19
4.3 Power Supply Connection 20
Settings 24
Peripherals 24
5.2.1 Direct Connection 25
5.2.3 Modem Connection 37
5.2.4 TCP Connection 45
5.2.5 Actions 48
PT 0011 49
• Channel I to Channel P 53
Selection 55
5.2.6 Extras 61
Caution 61
6 CM Editor 66
6.1 Menu Bar 67
6.1.2 CM Program 68
6.1.3 Grouping 72
6.1.4 Device 72
6.1.5 Sensor Constellation 73
6.1.6 Sensor Configuration 75
6.1.7 Extras 77
6.2 Window Divisions 78
7 CM Program Functions 79
7.1.2 Parameters 80
7.2 Data Sources 81
7.2.4 Numerical Entry 82
7.2.5 Boolean Entry 82
7.2.6 Time Sensor 83
7.2.7 Clock Timer 83
7.2.8 Error Event 84
7.2.9 Boolean Constants 84
7.2.10 State-bit 84
7.2.11 Sequency 85
7.3 Numerical Calculations 86
7.3.5 Division Remainder 87
7.3.6 Absolute Value 87
7.3.8 Rounding 87
7.3.10 Square Root 88
7.3.11 Power at Base e 88
7.3.12 Natural Logarithm 88
7.3.13 Decade Logarithm 89
7.3.14 Integral 89
7.3.15 Differential Quotient 90
7.4 Numerical Operations 91
7.4.5 Median Value 92
7.4.6 Note Value 92
7.4.7 Note Minimum 92
7.4.8 Note Maximum 93
7.4.9 Tabular Value 93
7.4.10 Tabular Index 94
7.4.11 Characteristic Curve 94
7.4.12 Slope 95
7.5 Counting Functions 96
7.6 Numerical Conditions 97
7.6.5 Less than 98
7.6.3 Greater than 98
7.6.6 Less than or Equal to 99
7.6.7 Within 99
7.6.8 Outside 99
7.7 Boolean Links 100
7.7.4 Or 101
7.7.5 Not - Or 101
7.7.6 Exclusive Or 102
7.7.7 Not Exclusive Or 102
7.8.1 Note Value 103
7.8.2 Switching Delay 103
7.8.3 T - Flipflop 104
7.8.4 Mono Flop 104
7.8.5 RS - Flipflop 105
7.8.6 Pulse Generation 105
7.9 Result Values 106
7.9.2 Boolean Output Value 107
7.10 Actions 108
7.10.3 Display Message 109
7.10.4 Switch on LED 109
7.10.7 Start new log 110
7.11 Other 111
9 Technical Data 117
9.6 Analog Outputs 118
9.7 Digital Outputs 118
9.8 Calculation Unit 118
9.9 Interfaces 118
9.10 Cycle Time 119
9.12 Dimensions and Weight: 119
9.13 Technical Standards 119
10 Ordering Details 120
11 Accessories 121

Comments to this Manuals

No comments

Hydac CMU 1000 User Manual Page 34

Comments to this Manuals

Related products and manuals for Equipment Hydac CMU 1000