Hydac CMU 1000 User Manual Page 92
- Page / 122
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Condition Monitoring Unit CMU 1000 Page 92
Revised 17.12.2009 HYDAC ELECTRONIC GMBH Mat.-No.: 669749
7.4.5 Median Value
The Median value funtion supplies the arithmetical median value of
the input values over an adjustable time range.
The time range is set in seconds with the Time parameter.
The formation of the median value is accomplished by means of the
"Repeating Average" procedure. This means that, when the time
setting is "2 seconds", for example, the input values are compiled for
2 seconds, then averaged and output at the output. The next median
value interval begins afterwards. The median value remains stopped
at the last median value thereby
Inputs x: Input value (Numerical)
Outputs: y: Median value (Numerical)
Parameters: p
1
: Time (Numerical)
7.4.6 Note Value
The Note value function is used to hold on to certain values (to
freeze them). It has one numerical and one Boolean input.
If the Boolean input value is "1", then the numerical input value is
output at the output. If the Boolean input value is "0", then the last
output value remains in effect.
If the value is only to be applied for one flank of the Boolean input,
then you can put the function Pulse generation upstream from it (see
Chap. 7.8.6).
Inputs x
1
: Input value (Numerical)
x
2
: Switch value through (Boolean)
Outputs: y: (Numerical)
Parameters: -
7.4.7 Note Minimum
The Note minimum function supplies as the output value the
smallest value that the input value has yet reached.
If the input value is greater than the output value, then the output
value remains unchanged. If the input value is less, then the output
value will be reset.
The minimum can be reset with the Boolean input x
2
. The input
value wil be applied directly at the output for as long as this input is
"1".
Inputs x
1
: Input value (Numerical)
x
2
: Reset (Boolean)
Outputs: y: (Numerical)
Parameters: -
- Condition Monitoring Unit 1
- CMU 1000 1
- Table of Contents 3
- Preface 8
- 1 General 9
- 1.3 Copyright Protection 10
- 1.4 Note on Warranty 10
- 2 Safety 11
- 2.2 Proper/Designated Use 12
- 2.3 System Configuration 12
- 3 Setup and Function 13
- 3.3 Terminal Allocations 14
- IO-Link 15
- 3.4 Examples of Connections 16
- 3.4.2 Standard HSI Sensors 17
- 3.4.5 GSM Module CSI-F-10 18
- 4.1 Installation Guidelines 19
- 4.3 Power Supply Connection 20
- Settings 24
- Peripherals 24
- 5.2.1 Direct Connection 25
- 5.2.3 Modem Connection 37
- 5.2.4 TCP Connection 45
- 5.2.5 Actions 48
- PT 0011 49
- • Channel I to Channel P 53
- Selection 55
- 5.2.6 Extras 61
- Caution 61
- 6 CM Editor 66
- 6.1 Menu Bar 67
- 6.1.2 CM Program 68
- 6.1.3 Grouping 72
- 6.1.4 Device 72
- 6.1.5 Sensor Constellation 73
- 6.1.6 Sensor Configuration 75
- 6.1.7 Extras 77
- 6.2 Window Divisions 78
- 7 CM Program Functions 79
- 7.1.2 Parameters 80
- 7.2 Data Sources 81
- 7.2.4 Numerical Entry 82
- 7.2.5 Boolean Entry 82
- 7.2.6 Time Sensor 83
- 7.2.7 Clock Timer 83
- 7.2.8 Error Event 84
- 7.2.9 Boolean Constants 84
- 7.2.10 State-bit 84
- 7.2.11 Sequency 85
- 7.3 Numerical Calculations 86
- 7.3.5 Division Remainder 87
- 7.3.6 Absolute Value 87
- 7.3.8 Rounding 87
- 7.3.10 Square Root 88
- 7.3.11 Power at Base e 88
- 7.3.12 Natural Logarithm 88
- 7.3.13 Decade Logarithm 89
- 7.3.14 Integral 89
- 7.3.15 Differential Quotient 90
- 7.4 Numerical Operations 91
- 7.4.5 Median Value 92
- 7.4.6 Note Value 92
- 7.4.7 Note Minimum 92
- 7.4.8 Note Maximum 93
- 7.4.9 Tabular Value 93
- 7.4.10 Tabular Index 94
- 7.4.11 Characteristic Curve 94
- 7.4.12 Slope 95
- 7.5 Counting Functions 96
- 7.6 Numerical Conditions 97
- 7.6.5 Less than 98
- 7.6.3 Greater than 98
- 7.6.6 Less than or Equal to 99
- 7.6.7 Within 99
- 7.6.8 Outside 99
- 7.7 Boolean Links 100
- 7.7.4 Or 101
- 7.7.5 Not - Or 101
- 7.7.6 Exclusive Or 102
- 7.7.7 Not Exclusive Or 102
- 7.8.1 Note Value 103
- 7.8.2 Switching Delay 103
- 7.8.3 T - Flipflop 104
- 7.8.4 Mono Flop 104
- 7.8.5 RS - Flipflop 105
- 7.8.6 Pulse Generation 105
- 7.9 Result Values 106
- 7.9.2 Boolean Output Value 107
- 7.10 Actions 108
- 7.10.3 Display Message 109
- 7.10.4 Switch on LED 109
- 7.10.7 Start new log 110
- 7.11 Other 111
- 9 Technical Data 117
- 9.6 Analog Outputs 118
- 9.7 Digital Outputs 118
- 9.8 Calculation Unit 118
- 9.9 Interfaces 118
- 9.10 Cycle Time 119
- 9.12 Dimensions and Weight: 119
- 9.13 Technical Standards 119
- 10 Ordering Details 120
- 11 Accessories 121
Related products and manuals for Equipment Hydac CMU 1000
Equipment Hydac HDA 5500 User Manual
(17 pages)
(17 pages)
Equipment Hydac CSI-F-10 User Manual
(120 pages)
(120 pages)
Equipment Hydac HLB 1400 User Manual
(18 pages)
(18 pages)
Equipment Hydac HLB 1300 User Manual
(46 pages)
(46 pages)
Equipment Hydac HMG 510 User Manual
(26 pages)
(26 pages)
Equipment Hydac HMG 3000 User Manual
(76 pages)
(76 pages)
Equipment Hydac HMG 500 User Manual
(28 pages)
(28 pages)
Equipment Hydac HPG 3000 User Manual
(21 pages)
(21 pages)
Equipment Hydac HMG 3010 User Manual
(86 pages)
(86 pages)
© 2020, manymanuals.com. All rights reserved. | 3.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals