Hydac CMU 1000 User Manual Page 38
- Page / 122
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Condition Monitoring Unit CMU 1000 Page 38
Revised 17.12.2009 HYDAC ELECTRONIC GMBH Mat.-No.: 669749
5.2.3.2 Establishing Connection with GSM Radio Module CSI-F-10
• Connect the CMU 1000 for configuring the CSI-F-10 GSM radio module to your
PC as also described in Chapter 5.2.1 Direct Connection, Chapter 5.2.2 Direct
Connection via HSI Bus or Chapter 5.2.4 TCP Connection.
• Start the HYDAC PC software CMWIN
• In the Units Menu, select the "CM Manager" option.
• If the Connection window does not open automatically, select
"Connection" in the menu bar of the CM Manager.
• Under Interface Settings make the settings necessary for the available
connection type (for configuring the CSI-F-10).
• Click on “OK“ to apply the settings or “Cancel“ to discard these changes. In
either case you will then return to the Connection window.
• Click on Open to open the selected interface. The opened interface is indicated
by a green dot at the top right.
• Select "Change" in the Pass-through mode line. The following window opens:
• In the drop-down menu, select "Port I" and then click on Switch on in order to
switch on the pass-through mode.
- Condition Monitoring Unit 1
- CMU 1000 1
- Table of Contents 3
- Preface 8
- 1 General 9
- 1.3 Copyright Protection 10
- 1.4 Note on Warranty 10
- 2 Safety 11
- 2.2 Proper/Designated Use 12
- 2.3 System Configuration 12
- 3 Setup and Function 13
- 3.3 Terminal Allocations 14
- IO-Link 15
- 3.4 Examples of Connections 16
- 3.4.2 Standard HSI Sensors 17
- 3.4.5 GSM Module CSI-F-10 18
- 4.1 Installation Guidelines 19
- 4.3 Power Supply Connection 20
- Settings 24
- Peripherals 24
- 5.2.1 Direct Connection 25
- 5.2.3 Modem Connection 37
- 5.2.4 TCP Connection 45
- 5.2.5 Actions 48
- PT 0011 49
- • Channel I to Channel P 53
- Selection 55
- 5.2.6 Extras 61
- Caution 61
- 6 CM Editor 66
- 6.1 Menu Bar 67
- 6.1.2 CM Program 68
- 6.1.3 Grouping 72
- 6.1.4 Device 72
- 6.1.5 Sensor Constellation 73
- 6.1.6 Sensor Configuration 75
- 6.1.7 Extras 77
- 6.2 Window Divisions 78
- 7 CM Program Functions 79
- 7.1.2 Parameters 80
- 7.2 Data Sources 81
- 7.2.4 Numerical Entry 82
- 7.2.5 Boolean Entry 82
- 7.2.6 Time Sensor 83
- 7.2.7 Clock Timer 83
- 7.2.8 Error Event 84
- 7.2.9 Boolean Constants 84
- 7.2.10 State-bit 84
- 7.2.11 Sequency 85
- 7.3 Numerical Calculations 86
- 7.3.5 Division Remainder 87
- 7.3.6 Absolute Value 87
- 7.3.8 Rounding 87
- 7.3.10 Square Root 88
- 7.3.11 Power at Base e 88
- 7.3.12 Natural Logarithm 88
- 7.3.13 Decade Logarithm 89
- 7.3.14 Integral 89
- 7.3.15 Differential Quotient 90
- 7.4 Numerical Operations 91
- 7.4.5 Median Value 92
- 7.4.6 Note Value 92
- 7.4.7 Note Minimum 92
- 7.4.8 Note Maximum 93
- 7.4.9 Tabular Value 93
- 7.4.10 Tabular Index 94
- 7.4.11 Characteristic Curve 94
- 7.4.12 Slope 95
- 7.5 Counting Functions 96
- 7.6 Numerical Conditions 97
- 7.6.5 Less than 98
- 7.6.3 Greater than 98
- 7.6.6 Less than or Equal to 99
- 7.6.7 Within 99
- 7.6.8 Outside 99
- 7.7 Boolean Links 100
- 7.7.4 Or 101
- 7.7.5 Not - Or 101
- 7.7.6 Exclusive Or 102
- 7.7.7 Not Exclusive Or 102
- 7.8.1 Note Value 103
- 7.8.2 Switching Delay 103
- 7.8.3 T - Flipflop 104
- 7.8.4 Mono Flop 104
- 7.8.5 RS - Flipflop 105
- 7.8.6 Pulse Generation 105
- 7.9 Result Values 106
- 7.9.2 Boolean Output Value 107
- 7.10 Actions 108
- 7.10.3 Display Message 109
- 7.10.4 Switch on LED 109
- 7.10.7 Start new log 110
- 7.11 Other 111
- 9 Technical Data 117
- 9.6 Analog Outputs 118
- 9.7 Digital Outputs 118
- 9.8 Calculation Unit 118
- 9.9 Interfaces 118
- 9.10 Cycle Time 119
- 9.12 Dimensions and Weight: 119
- 9.13 Technical Standards 119
- 10 Ordering Details 120
- 11 Accessories 121
Related products and manuals for Equipment Hydac CMU 1000
Equipment Hydac HDA 5500 User Manual
(17 pages)
(17 pages)
Equipment Hydac CSI-F-10 User Manual
(120 pages)
(120 pages)
Equipment Hydac HLB 1400 User Manual
(18 pages)
(18 pages)
Equipment Hydac HLB 1300 User Manual
(46 pages)
(46 pages)
Equipment Hydac HMG 510 User Manual
(26 pages)
(26 pages)
Equipment Hydac HMG 3000 User Manual
(76 pages)
(76 pages)
Equipment Hydac HMG 500 User Manual
(28 pages)
(28 pages)
Equipment Hydac HPG 3000 User Manual
(21 pages)
(21 pages)
Equipment Hydac HMG 3010 User Manual
(86 pages)
(86 pages)
Century Jouets et accessoires manuels d'utilisation
À partir de B
Comments to this Manuals